[ale] CD burner problems

[ChangingLINKS.com]

data. (I have used the command before to do the same thing).

Drew


On Monday 12 May 2003 01:31 pm, Josh Freeman wrote:
> Are you trying to make an audio cd or a data cd?
>
> Josh
>
> On Mon, 2003-05-12 at 14:25, ChangingLINKS.com wrote:
> > I am having a problem gettng my CD burner to work under Suse. Below is
> > the output of what is happened (looks like it is going to work and fails
> > "OPC"). Anyone else run into this problem?
> >
> > Cdrecord 1.11a28 (i686-suse-linux) Copyright (C) 1995-2002 Jörg Schilling
> > TOC Type: 1 = CD-ROM
> > Using libscg version 'schily-0.6'
> > atapi: 1
> > Device type    : Removable CD-ROM
> > Version        : 0
> > Response Format: 1
> > Vendor_info    : 'IDE-CD  '
> > Identifikation : 'R/RW 4x4x24     '
> > Revision       : 'C12a'
> > Device seems to be: Generic mmc CD-RW.
> > Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> > Driver flags   : SWABAUDIO
> > Supported modes: TAO PACKET RAW/R16
> > Drive buf size : 1572864 = 1536 KB
> > FIFO size      : 4194304 = 4096 KB
> > Track 01: data    19 MB
> > Total size:       22 MB (02:14.21) = 10066 sectors
> > Lout start:       22 MB (02:16/16) = 10066 sectors
> > Current Secsize: 2048
> > ATIP info from disk:
> >   Indicated writing power: 6
> >   Is not unrestricted
> >   Is not erasable
> >   Disk sub type: Medium Type C, low Beta category (C-) (6)
> >   ATIP start of lead in:  -11231 (97:32/19)
> >   ATIP start of lead out: 359848 (79:59/73)
> > Disk type:    Short strategy type (Phthalocyanine or similar)
> > Manuf. index: 27
> > Manufacturer: Prodisc Technology Inc.
> > Blocks total: 359848 Blocks current: 359848 Blocks remaining: 349782
> > Starting to write CD/DVD at speed 4 in real TAO mode for single session.
> > Last chance to quit, starting real write in 9 seconds.          8
> > seconds. 7 seconds.          6 seconds.          5 seconds.          4
> > seconds. 3 seconds.          2 seconds.          1 seconds.          0
> > seconds. Operation starts.
> > Waiting for reader process to fill input buffer ... input buffer ready.
> > Performing OPC...
> >
> > cdrecord: Input/output error. send opc: scsi sendcmd: no error
> > CDB: 54 01 00 00 00 00 00 00 00 00 00
> > status: 0x2 (CHECK CONDITION)
> > Sense Bytes: 70 00 03 00 00 00 00 13 00 00 00 00 00 73 00 00
> > Sense Key: 0x3 Medium Error, Segment 0
> > Sencse Code: 0x73 Qual 0x03 (power calibration area error) Fru 0x0
> > Sense flags: Blk 0 (not valid)
> > cmd finished after 7.3s timeout 60s
> > cdrecord: OPC failed.
> > cdrecord: fifo had 64 puts and 0 gets.
> > cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
> > --
> > Wishing you Happiness, Joy and Laughter,
> > Drew Brown
> > http://www.ChangingLINKS.com
> > _______________________________________________
> > Ale mailing list
> > Ale at ale.org
> > http://www.ale.org/mailman/listinfo/ale

-- 
Wishing you Happiness, Joy and Laughter,
Drew Brown
http://www.ChangingLINKS.com
_______________________________________________
Ale mailing list
Ale at ale.org
http://www.ale.org/mailman/listinfo/ale