Chris,
You can edit /etc/pcmcia/config.opts.
Chris Coleman
Clayton College and State University
email: ">ChrisColeman@mail.clayton.edu
(770) 960-4282
> -----Original Message-----
> From: Chris Fowler [SMTP:">chrisf@computone.com]
> Sent: Thursday, January 13, 2000 11:35 AM
> To: '">ChrisColeman@mail.clayton.edu'
> Cc: '">ale@ale.org'
> Subject: RE: [ale] Linux PCMCIA
>
> I have no SCSI cars. This is a Toshiba Satellite 2535CDS. Is there a way
> I
> can tell cardservices to use something different?
>
> Chris
>
> -----Original Message-----
> From: ">ChrisColeman@mail.clayton.edu
> [mailto:">ChrisColeman@mail.clayton.edu]
> Sent: Thursday, January 13, 2000 2:28 PM
> To: ">chrisf@computone.com; ">ale@ale.org
> Subject: RE: [ale] Linux PCMCIA
>
>
> Chris,
>
> Card and socket services attempted to locate an upper memory address to be
> used with your 3com card. It searched 0xd0000 - 0xfffff and could not
> locate
> a window large enough to support the memory I/O for your card.
>
> Do you have adapter cards installed that have a ROM BIOS installed and
> enabled? Maybe a SCSI adapter with an enabled BIOS? It appears that
> something may be using this area.
>
> Chris Coleman
> Clayton College and State University
> email: ">ChrisColeman@mail.clayton.edu
> (770) 960-4282
>
> > -----Original Message-----
> > From: Chris Fowler [SMTP:">chrisf@computone.com]
> > Sent: Thursday, January 13, 2000 9:40 AM
> > To: '">ale@ale.org'
> > Subject: [ale] Linux PCMCIA
> >
> > Can anyone tell me what the following message means:
> >
> > Linux PCMCIA Card Services 3.0.13
> > kernel build: 2.2.12 unknown
> > options: [pci] [cardbus] [apm]
> > Intel PCIC probe:
> > Toshiba ToPIC97 PCI-to-CardBus at bus 0 slot 19, mem 0x68000000, 2
> > sockets
> > host opts [0]: [slot 0xf0] [ccr 0x10] [cdr 0x86] [rcr 0x02] [no pci
> > irq]
> > [lat 168/176] [bus 20/20]
> > host opts [1]: [slot 0xf0] [ccr 0x20] [cdr 0x86] [rcr 0x02] [no pci
> > irq]
> > [lat 168/176] [bus 21/21]
> > ISA irqs (default) = 3,4,5,7,10,12 polling interval = 1000 ms
> > cs: IO port probe 0x1000-0x17ff: clean.
> > cs: IO port probe 0x0100-0x04ff: excluding 0x220-0x22f 0x330-0x337
> > 0x378-0x37f 0x388-0x38f 0x480-0x48f 0x4d0-0x4d7
> > cs: IO port probe 0x0a00-0x0aff: clean.
> > cs: memory probe 0x0d0000-0x0dffff: excluding 0xd0000-0xdffff
> > cs: memory probe 0x0c0000-0x0cffff: excluding 0xc0000-0xcffff
> > cs: memory probe 0x0e0000-0x0effff: excluding 0xe0000-0xeffff
> > cs: memory probe 0x0f0000-0x0fffff: excluding 0xf0000-0xfffff
> > cs: unable to map card memory!
> > cs: unable to map card memory!
> > memory_cs: RequestWindow: Resource in use
> >
> >
> > I can install RedHat over the network via ftp using a 3Com 10/100 LAN
> > CardBus Model 3CCFE575BT. But when I boot after install the network
> does
> > not work.
> >
> > Thanks,
> > Chris Fowler
> > --
> > To unsubscribe: mail ">majordomo@ale.org with "unsubscribe ale" in message
> > body.
> --
> To unsubscribe: mail ">majordomo@ale.org with "unsubscribe ale" in message
> body.
--
To unsubscribe: mail ">majordomo@ale.org with "unsubscribe ale" in message body.